KEYENCE BL-U2 MANUAL PDF

August 2, 2019 posted by

BL-U2, Dedicated Communication Unit (for RSC) in BL-U1・U2/N・48 by KEYENCE INTERNATIONAL (BELGIUM). KEYENCE BL Series User Manual • Appendices, Bl-u2, N • KEYENCE Sensors. KEYENCE BL Series User Manual • Bl-u2, N, Viii • KEYENCE Sensors.

Author: Vusho Yom
Country: Estonia
Language: English (Spanish)
Genre: Medical
Published (Last): 13 November 2008
Pages: 26
PDF File Size: 6.68 Mb
ePub File Size: 8.46 Mb
ISBN: 378-1-85331-177-3
Downloads: 80591
Price: Free* [*Free Regsitration Required]
Uploader: Tojabei

Guaranteed by Sat, Jan 5. Read the “Limit 2 — digit settings” barcode. A-7 Barcode symbology settings. Page 44 Decode Settings Duplicate Read Prevention settings No reread prevention After reading the “Start duplicate read prevention time settings” barcode above, read three barcodes for the decimal program code page to set the time. Limit meyence settings 1.

Power Supply Unit

Settings surrounded by are factory default. We do our best to describe everything. The time can be set between and 15, ms in ms intervals. Manaul 24 Trigger Modes Select one of the following operation modes depending on the application. Otherwise, the BL- Series may be damaged. Page 21 3 Scanning Barcodes 3 Scanning. Tell us about it. Otherwise, generated noise may cause product failure or malfunctions. Guaranteed Delivery see all.

We are happy to help where we can, but it is your sole responsibility to resolve all import issues. If the unit is dropped or shocked, it may be damaged. This laser has a wavelength of nm and is classified as a Class 1 laser under IEC Safety of laser products. Changes to the BL-N70 family program settings are made by scanning the setup codes found in this chapter.

Modular jack tab Communication cable connecto Modular jack Gently pull on the cord protector for the connection cable to verify mwnual it is locked into place. If we fail your expectations,we want to make it right.

  ER1602CT DATASHEET PDF

A-4 Settings and the Factory Default Values Setting item Function to limit the ieyence of digits for reading Setting content Limit all settings Disabled Enabled Limited digits to Limit block 1 Digits to Code types tototo Limit block 2 Digits to Code types tototo Limit block 3 Digits to Code types tototo Limit block 4 Digits to Code types toto Scans bars as narrow as 0.

If your application requires more speed, you can set the Decode Match Count to 1. Using a different voltage level may damage the unit. Introduction This manual contains information about procedures for handling, operations, warnings, and precautions about the “Hand-held Laser Barcode Reader BL-N70 Series”.

KEYENCE BL-N70 Series : Manual

Keep this manual in a safe place after reading it so that it can be used at any time. Read the decimal program codes “0,” “8,” and “1. Show only see all. Read the “Laser off time setting” barcode.

Use of controls or adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

Buying Format see all. Page 52 Decimal Program Code Use these barcodes to set the laser off time for trigger switch operation mode pagereread prevention time pagethe number of digits for the limit read digits function, and when setting the code type page Before beginning operation, please read this manual carefully to get the most from your BL Series.

Make sure that power is not being supplied to the BL-N70 series when replacing the communication cable. Or point us to the URL where the manual is located.

  DVANAEST RIMSKIH CAREVA PDF

Read the “Limit 1 — digit settings” barcode. To set the number of digits, scan three decimal barcodes from page Using other power sources may cause damage.

If poor print quality, or other conditions are causing problems with decode reliability, try setting the Decode Manuap Count to a number higher than 2.

Appendices, Bl-u2, N-42 – KEYENCE BL-700 Series User Manual

Warning Labels 1 Warning Labels 3. We are eager to assist you in making the correct choice. Warning Labels 1 Warning Labels. Page 69 A-5 Replacing the Communication Cable z Connecting the communication cable 1 Insert the modular jack for the replacement communication cable into the connector for the BL-N70 cable. Do not disassemble or modify the BL-N70 series. Class 2 Laser Product. Using a different voltage. Raster High-Res, 9-pin Fe. The H is a High resolution, side scanner, Raster unit.

Supply power by using the included AC adapter. Labels Location Warning labels are attached to the sensor head as shown below. Within 2 miles 5 miles 10 miles 15 miles 20 miles 50 miles 75 miles miles miles miles miles miles miles miles miles of.

We directly accept US issued credit cards.

During this time, a new barcode cannot be scanned. Read the decimal program codes “0,” “0,” and “8. Click on the [Finish] button. Does not include stand. Page 9 1 1 Getting Started Getting Started This chapter explains the package contents, the names and functions of each part, and the basic methods for operation.